亚洲AV日韩AV无码AV

                新聞動態
                 電爐溫度電壓的控制程序運行

                在使用電爐的時候應該最在意的就是溫度了吧,溫度是由一個程序來進行控制的,下面我么具體來看看電爐溫度電壓的控制程序運行。
                In the use of electric furnace should be the most concerned about is the temperature, the temperature is controlled by a program, let's take a look at the electric furnace temperature and voltage control program operation.
                在初次使用電爐的時候要先看下使用說明書,新爐子在使用前要進行3小時低溫段烘烤,因為爐膛材質使用要磨合下,還可以除去里面的水分,防止爐膛高溫時候破裂。
                When using the electric furnace for the first time, you should read the operation manual first. Before using the new furnace, you should bake it at low temperature for 3 hours, because the furnace material needs to be run in, and the moisture inside can be removed to prevent the furnace from cracking at high temperature.
                首次使用接電源線時候,應接到符合功率要求的空氣開關上,空氣開關上的到設備之間的電源線不能盤卷在一起,特別是功率大的設備。
                When using the power cord for the first time, it should be connected to the air switch that meets the power requirements. The power cord from the air switch to the equipment cannot be coiled together, especially for the equipment with high power.


                在抽真空前把門關上,鎖緊緊固件。把真空泵的一段氣管接在設備的一個氣閥上,另外一個氣閥關閉,打開真空泵,當電爐上的壓力表讀數到-0.1的時候關閉抽氣閥門,然后在關閉真空泵,順序不能反,不然會造成真空泵內的油反吸到爐子內的現象。
                Close the door and lock the fasteners before vacuumizing. Connect one section of the air pipe of the vacuum pump to one valve of the equipment, close the other valve, open the vacuum pump, close the air extraction valve when the pressure gauge on the electric furnace reaches - 0.1, and then close the vacuum pump in reverse order, otherwise the oil in the vacuum pump will be sucked back into the furnace.
                抽完真空后可以充入你需要通入的氣氛,把通氣氛的氣管接上進氣閥,打開氣氛,電爐前面有個流量計的,也可以控制通入氣氛的流量,當壓力表的指針回到零刻度的時候就可以了,關閉氣氛。
                After vacuumizing, you can fill in the atmosphere you need. Connect the air pipe to the air inlet valve and open the atmosphere. There is a flowmeter in front of the electric furnace, which can also control the flow of the atmosphere. When the pointer of the pressure gauge returns to the zero scale, you can close the atmosphere.
                電爐在升溫過程前自己設定好需要的參數,然后運行程序。在高溫時候建議不要打開爐門,因為極冷極熱會影響到加熱元件的使用壽命。
                Before heating up, the furnace sets the required parameters and then runs the program. It is recommended not to open the furnace door at high temperature, because extremely cold and extremely hot will affect the service life of heating elements.
                加熱元件如果壞了的話可以自己更換。如果是電鍍絲的加熱元件則需要專業人員進行更換,難度比較大。
                If the heating element is broken, it can be replaced by itself. If it is the heating element of electroplating wire, it needs to be replaced by professionals, which is difficult.

                 
                 油罐車海底閥 鋼鋁復合暖氣片 淄博不銹鋼管廠家 燃氣回轉爐 天津紙盒
                濟南金岳電爐制造有限公司 版權所有(C)2014   網絡支持   股票代碼: 002095 著作權聲明 網站管理 魯ICP備14033186號-1
                亚洲AV日韩AV无码AV